Page 1 of 1
Round Arc
Posted: Tue Feb 09, 2016 8:07 pm
by benDragon81037
Hey there.
I have another problem, how do you round an arc intersecting an elipse? I kinda need to make a transition curve between the elipse and the arc here shown by the blue entities:
Re: Round Arc
Posted: Tue Feb 09, 2016 9:47 pm
by Husky
Hi,
the easiest way would be:
select the ellipse,
"Explode" the ellipse what will change it to a polyline,
launch the Modify -> Round tool to make the transition.
Note: Exploding the eclipse could lead to a slightly different ellipse / Polyline shape depending on your "Application preferences / Modify / Explode" settings .
- Husky-2016.02.09-02.png (12.32 KiB) Viewed 12050 times
Re: Round Arc
Posted: Tue Feb 09, 2016 10:53 pm
by benDragon81037
Thanks for the quick reply.
I tried to explode the elipse, as shown here:
Unfortunately, it says "The two entities cannot be rounded."
Re: Round Arc
Posted: Tue Feb 09, 2016 11:17 pm
by Husky
benDragon81037 wrote:Unfortunately, it says "The two entities cannot be rounded."
That sounds like the chosen radius wasn't working (to big / to small?).
Could you attach this dxf to your post?
Re: Round Arc
Posted: Tue Feb 09, 2016 11:29 pm
by benDragon81037
Hey there.
Alright, but it will look a little busy with all of the construction lines (stitches / guides) that I've placed to create an accurate blueprint.
Re: Round Arc
Posted: Wed Feb 10, 2016 12:59 am
by Husky
Thanks for the example drawing!
Ok, your drawing unit is Meter,
To make that transition I made the "Overlay 2" Layer active,
worked on Top projection / left side
started the round tool,
chose a radius of 0.2,
clicked both lines and it was working as expected.
- Husky-2016.02.09-04.png (2.49 KiB) Viewed 12040 times
Note: Top projection right side / ellipse isn't exploded.
Re: Round Arc
Posted: Wed Feb 10, 2016 1:35 am
by benDragon81037
Yeah, I exploded only one corner to test if it worked, unfortunately, I keep getting the "The two entities cannot be rounded". Error message, which I keep on getting.
Re: Round Arc
Posted: Wed Feb 10, 2016 1:54 am
by Husky
benDragon81037 wrote:Yeah, I exploded only one corner to test if it worked...
That is what I thought.
benDragon81037 wrote:... unfortunately, I keep getting the "The two entities cannot be rounded". Error message, which I keep on getting.
Ok, then I have additional questions ...
Question 1:
What is your radius size?
Question 2
You are using the radius value with a dot or a comma? If yes try to use a dot instead of a comma and/or vice versa.
Re: Round Arc
Posted: Wed Feb 10, 2016 9:57 am
by Clive
Hi benDragon81037
Something like this ?
- Arc Fit 1.jpg (40.83 KiB) Viewed 11835 times
- Arc Fit 2.jpg (50.82 KiB) Viewed 11835 times
Re: Round Arc
Posted: Wed Feb 10, 2016 1:45 pm
by benDragon81037
Yeah, something like that.
The radius size is 0.2 (I tried 0,2, but it ended up making the radius 2 which is too big, it also was 0.15 / 0,15), both the 0.2 and 0,2 ended up with the same result though.
Re: Round Arc
Posted: Thu Feb 11, 2016 9:44 pm
by benDragon81037
Say, my blueprint's nearly finished, the last problem I'd like to solve would be this single problem, but I'd really like an answer to my delima.
Re: Round Arc
Posted: Fri Feb 12, 2016 3:16 pm
by Clive
Hi benDragon81037
See attached your drawing, which I have edited to suit your request for 'rounding' off. I've saved it as R15 DXF, so you should be able to open this with the Community Version.
- Rev 1CT.jpg (85.68 KiB) Viewed 11791 times
- Rev 1CT2.jpg (23.03 KiB) Viewed 11791 times
- Rev 1CT3.jpg (25.03 KiB) Viewed 11791 times
All you need to do is select the yellow entities and change layer/Colour.
Regards
Clive
Re: Round Arc
Posted: Fri Feb 12, 2016 3:39 pm
by benDragon81037
Thank you for posting the fixed version, and yes, it does solve that problem and only that problem (by getting you to do it for me), but I don't think that doing stuff for me is good for me in the long term when I may need to do this again.
Re: Round Arc
Posted: Fri Feb 12, 2016 4:13 pm
by Clive
Sure I understand and glad to hear it.
The number One thing to do is trial the Pro version, the modify tools are quite something, the best I've seen in a 2D CAD program.
You stated initially that you wanted to 'round' off, so my way forward was to use a Spline to do the job:
1. Set up new layer - 'Construction'.
2. On this layer work out and place points for reference.
3.Using the Spline tool, draw a Spline (with controlled points) between my construction points.
4. Use the modify tools, break out segment and Divide I cleaned up the drawing.
Hope this helps.
Clive
Re: Round Arc
Posted: Fri Feb 12, 2016 10:35 pm
by benDragon81037
Do you think you could put illustrations?